Die Suche ergab 127 Treffer

von BalladExchangeDB
Samstag 9. Juli 2011, 09:17
Forum: Accommodation
Thema: Table stability
Antworten: 1
Zugriffe: 15802

Re: Table stability

msn-patentnick1 wrote on Jul 8, '04 My table wobbles a little but not nearly as much as you describe. A single leg support would work but only for the cockpit where you can mount the base on the cockpit sole and secure it with a large backing plate underneath. Inside, the location of the bilges pre...
von BalladExchangeDB
Samstag 9. Juli 2011, 09:15
Forum: Accommodation
Thema: Table stability
Antworten: 1
Zugriffe: 15802

Table stability

My table was loos. It would woble if touched it, and the whole dinner would fall into the seats if I pushed it when sitting myself down. The one base was loos, the other leg was broken and stuffed with a wooden rod. I converted the table to a one legged table, hoping the new stuff would be stiffer, ...
von BalladExchangeDB
Samstag 9. Juli 2011, 09:14
Forum: Accommodation
Thema: The Trawler Kerosene Lamp
Antworten: 1
Zugriffe: 15811

Re: The Trawler Kerosene Lamp

msn-falmouthballad1 wrote on Oct 19, '05 Hi Jesper Thanks. It looks a good arrangement for fixing the Trawler lamp. Has it stayed in place when you have been out in a blow going to windward? Best wishes David msn-patentnick1 wrote on Nov 15, '05 Hi Jesper: After a few back-and-forths between a UK d...
von BalladExchangeDB
Samstag 9. Juli 2011, 09:13
Forum: Accommodation
Thema: The Trawler Kerosene Lamp
Antworten: 1
Zugriffe: 15811

The Trawler Kerosene Lamp

We have a kerosene lamp onboard that is very cosy. It is called the Trawler Lamp, and you may buy it from a lot of places but here is a link to one place and a description of the lamp: http://www.oillampman.com/denhaan/trawler1.htm. The lamp does not supply too much lighting, even though if we run o...
von BalladExchangeDB
Samstag 9. Juli 2011, 09:04
Forum: Engine
Thema: Folding prop choice
Antworten: 1
Zugriffe: 52870

Re: Folding prop choice

maccormac reply maccormac wrote on Nov 25, '09 We installed the same Beta 20 engine at the start of the season and have been running with a Flex-o-fold 14x9 two blade folding prop from Darglow Engineering ( 01929 556 512 ask for Bob) I wanted hull speed in flat water at around 2600/2700 revs. We ar...
von BalladExchangeDB
Samstag 9. Juli 2011, 09:02
Forum: Engine
Thema: Folding prop choice
Antworten: 1
Zugriffe: 52870

Folding prop choice

Dear Balladeers, We are looking at replacing our fixed 3 bladed 13x9 prop with a two blade folding prop, firstly to go faster under sail, and secondly as the current selection seems underpropped. We have a Betamarine 20hp with 2:1 reduction on the gearbox. Max engine revs are 3600 in theory, but we ...
von BalladExchangeDB
Samstag 9. Juli 2011, 09:01
Forum: Engine
Thema: Nanni Diesel Engine installation and exhaust outlet modifica
Antworten: 1
Zugriffe: 18141

Re: Nanni Diesel Engine installation and exhaust outlet modi

patentnick wrote on Feb 17, '10 Hi Jere: I noticed that you have re-powered with a Nanni diesel. I've been looking at that particular engine for some time. Could you post some more photos of the installation? If not, could you please forward them to my e-mail: nicholas@thesyndicate.gr Thanks, Nicho...
von BalladExchangeDB
Samstag 9. Juli 2011, 09:00
Forum: Engine
Thema: Nanni Diesel Engine installation and exhaust outlet modifica
Antworten: 1
Zugriffe: 18141

Nanni Diesel Engine installation and exhaust outlet modifica

Nanni Diesel Engine installation and exhaust outlet modification
von BalladExchangeDB
Samstag 9. Juli 2011, 08:58
Forum: Engine
Thema: Yanmar engine pictures
Antworten: 1
Zugriffe: 16419

Re: Yanmar engine pictures

jereku wrote on May 2, '09 Hi everybody! At generally there might be a very important matter when installing a new engine in Ballad. Older engines were much higher than a new ones. Therefore the height between old exhaust muffler (water level in muffler!!) and exhaust outlet at new engine is less t...
von BalladExchangeDB
Samstag 9. Juli 2011, 08:58
Forum: Engine
Thema: Yanmar engine pictures
Antworten: 1
Zugriffe: 16419

Yanmar engine pictures

Hi everybody! I'm reinstalling my Windows on a new hard disk, and finding my pictures in different hiding places. I found the pictures of the Yanmar installation. The engine in the pictures is the 2YM15. The extra 10 cm space on the shaft should make room even for the 3ym20 engine, since the three c...
von BalladExchangeDB
Samstag 9. Juli 2011, 08:55
Forum: Engine
Thema: Rocker shaft
Antworten: 1
Zugriffe: 16097

Re: Rocker shaft

maccormac wrote on Feb 23, '09
I have a MD6A which I am willing to split for parts.
Does anyone out there know if the shaft is compatible?
von BalladExchangeDB
Samstag 9. Juli 2011, 08:55
Forum: Engine
Thema: Rocker shaft
Antworten: 1
Zugriffe: 16097

Rocker shaft

Has anyone got a compatible shaft for an MD7a?

The nuts on the turrets became lose on my engine this season and the shaft got broken.
von BalladExchangeDB
Samstag 9. Juli 2011, 08:54
Forum: Engine
Thema: MD6A-Broken freshwater drainage cock
Antworten: 0
Zugriffe: 15788

MD6A-Broken freshwater drainage cock

Hi, When ovehauling this season I was about to exchange the freshwater in the engine and doing this I broke of the drainage cock's joint in the engine (see the red circle in the picture) leaving just the threaded part remaining in the engine block. Since the cocks joint to the engine is at an downwa...
von BalladExchangeDB
Samstag 9. Juli 2011, 08:53
Forum: Engine
Thema: Propeller shaft dimensions
Antworten: 1
Zugriffe: 15990

Re: Propeller shaft dimensions

msn-gem2martin wrote on Sep 7, '08 I re-engined Alte Liebe, #1266, last year and retained the 25mm shaft as the Volvo coupling extactly mated the Yanmar output coupling. I ended up buying a new gori folding prop. The Gori rep who happened to be at the San Francico Boat show next the my prop shop lo...
von BalladExchangeDB
Samstag 9. Juli 2011, 08:52
Forum: Engine
Thema: Propeller shaft dimensions
Antworten: 1
Zugriffe: 15990

Propeller shaft dimensions

Hi Everyone, Thanks to everyone who responded to my earlier email on repowering with a Beta Marine diesel. We have decided to go with the 16 hp model. Now we need to buy a new right hand propeller and want to make sure I get something that will fit the existing propeller shaft before I place the ord...